|
|
HOOK
AND LOOP
PRESSURE
SENSITIVE - TEST REPORT
Adhesive
Backing Hook & Loop Fasteners
| Rubber
Base |
|
For
attachment to a wide range of substrates
Such as: Aluminum, Ceramics, Foams, Fabrics, Glass, Metal, Paper,
Wood, and Drywall.etc. |
| |
|
Adhesive
Description
Color: yellowish |
| |
|
| Hot
melted pressure sensitive adhesive with a high conversion viscosity,
suited for roll or slot-die coating, and displaying moderate
bond strength to various materials. |
| |
|
| Physical
Properties (Typical Values) |
|
Softening
point:
(DIN 52011, ASTMD 2398)
Peel adhesion at 180° |
228°F |
| After
20 min: |
54
oz/inch |
| After
24 h: |
54
oz/inch |
| |
|
| Shear
|
|
| At
68°F (500g/0.25 inch2) |
1200
min |
| At
104°F (1000g/0.5 inch2) |
67 min |
| |
|
Shear
adhesion failure
Temperature (SAFT):
(0.5°c/min 1000g/0.5 inch2) |
111°F
|
| |
|
| Loop
Tack (Finat 9) |
115
oz/inch |
| Rolling
Ball |
16 in |
| |
|
|
Brookfield Measuring System / Viscosity (cps x 1,000)
Temparature
(°F)
|
IMPORTANT NOTICE TO PURCHASER
All
Statements, technical advice and recommendations contained
herein are based on tests believed to be reliable, but the
accuracy thereof is not guaranteed, and the following is
made in lieu of all warranties, expressed or implied: seller’s
and manufacturer’s only obligation shall be to replace
the quantity of product proved to be defective. Neither
seller nor manufacturer shall be liable for any injury,
loss or damage, direct or consequential, arising out of
the use of or the inability to use the product. Before using,
user shall determine the suitability of the product for
his intended use, and user assumes all risk and liability
whatsoever in connection therewith. No statement or recommendation
not contained herein shall have any force or effect unless
in an agreement signed by officers of seller and manufacturer.
|
Adhesive Backing Hook & Loop Fasteners
Acrylic
Base (3M Brand #9485)/High temperature resistant
For attachement to a wide range of substructes such as stainless
steel, alumium, glass…etc.
Excellent shear holding power, as well as excellent high temperature
and UV resistance.
Typical
Adhesion Properties
Not for specification purposes
Peel Strength:
Peel Adhesion (ASTM Test Method)
(180° Peel, Room Temperature Conditions)
|
Surface |
9485 |
|
15 Min Dwell |
72 Hr Dwell |
|
oz/in |
(N/100 mm) |
oz/in |
(N/100 mm) |
|
Stainless Steel |
105.00 |
(114.00) |
150.00 |
(164.00) |
|
Aluminum |
45.00 |
(49.00) |
95.00 |
(104.00) |
|
Painted Metal |
70.00 |
(76.00) |
145.00 |
(158.00) |
|
Glass |
120.00 |
(131.00) |
145.00 |
(158.00) |
|
Polycarbonate |
115.00 |
(125.00) |
135.00 |
(147.00) |
|
Acrylic |
100.00 |
(109.00) |
125.00 |
(136.00) |
|
Epoxy |
85.00 |
(93.00) |
120.00 |
(131.00) |
|
ABS |
70.00 |
(76.00) |
85.00 |
(93.00) |
|
Rigid PVC |
50.00 |
(55.00) |
90.00 |
(98.00) |
|
Polypropylene |
50.00 |
(55.00) |
60.00 |
(65.00) |
|
LD. Polyethylene |
35.00 |
(38.00) |
40.00 |
(44.00) |
|
H.D.Polyethylene |
30.00 |
(33.00) |
35.00 |
(38.00) |
Shear Strength:
Static Shear Adhesion (ASTM Test Method)
(1" x 1" Area Contact -Aluminum to a Stainless Steel-72
hr dwell)
|
Temperature |
Load |
9485 |
| F |
C |
Grams |
Minutes
to Failure |
| 72 |
22 |
1,000 |
No
Failures-Tests Discontinued After 10,000 Min. |
| 158 |
70 |
400 |
| 200 |
93 |
400 |
| 250 |
121 |
300 |
| 300 |
149 |
300 |
| 350 |
177 |
300 |
| 450 |
232 |
200 |
|
|
Physical Properties and Performance Characteristics
| |
Products |
| |
9485
|
|
| Adhesive
Type |
A-25
Firm Acrylic
|
|
| Adhesive
Carrier |
None
|
1
mil (0.025 mm)Polyester
|
| Release
Liner |
Moisture
Resistant Tan Paper
|
|
Approximate
Thickness:
Release liner
Tape Only |
0.004
in
(0.10
mm)
0.005
in
(0.13
mm)
|
|
| Tape
Color |
Clear
|
|
Adhesion
To Steel
(ASTM Test Methods) |
Typical
Values-Not for Specification Purposes |
|
|
150
oz./in.
|
|
|
(163
N/100 mm)
|
|
Relative
High Temperature
Operating Ranges: |
Long
Term: (Day, Weeks)
|
300°F
(149°C)
|
|
| Short
Term: (Minutes, Hours) |
450°F
(232°C)
|
|
| Relative
SolventResistance |
Very
Good
|
|
| UV
Resistance |
Excellent
|
|
| Shelf
Life of Tape In Roll Form |
12
months from date of receipt by customer when stored in
original cartons at 70°F (21°C) and 50% relative
humidity. |
|
| |
|
| Application
Techniques |
Bond
strength is dependent on the amount of adhesive-to-surface contact
developed. Firm application pressure helps develop better adhesive
contact and improve bond strength.
To obtain optimum adhesion, the bonding surfaces must be clean,
dry, and well unified. t be clean, dry, and well unified.
Ideal tape application temperature range is 70°F to 100°F(21°C
to 38°C).Initial tape application to surfaces at temperatures
below 50°F (10°C) is not recommended because the adhesive
becomes too firm to adhere readily. However, once properly applied,
low temperature holding is satisfactory. |
| Important
Notice |
3M
MAKES NO WARRANTIES, EXPRESS OR IMPLIED, INCLUDING, BUT NOT
LIMITED TO. ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS
FOR A PARTICULAR PURPOSE. User is responslble for detemrining
whether the 3M product is fit for a particular purpose and suitable
for user's method of application. Please remember that many
factors can affect the use and performance of a 3M ITSD product
in a particular application. The materials to be bonded with
the product, the surface preparation of those materials, the
product selected for use, the conditions in which the product
is used and the time and environmental conditions in which the
product is expected to perform are among the many factors that
can affect the use and performance of a 3M ITSD product. Given
the variety of factors that can affect the use and performance
of a 3M ITSD product, some of which are uniquely within the
user's knowledge and control, it is essential that the user
evaluate the 3M ITSD product to determine whether it is fit
for a particular purpose and suitable for the user's method
of application. |
|
|
|
|
